CFM Performance: Yamaha Raptor 700 performance-enhancing, custom upgrade parts

CFM Performance

CFM Performance: Product Lines: Yamaha Raptor 700

(click image for larger photo) Yamaha Raptor 700 Cooler
Original 20 fin billet aluminum engine cooler called the CFM Hydrocooler. Manufactured by CFM Performance. Don't be fooled by cheap imitations. The CFM Hydrocooler was designed and built by professionals specifically for your Yamaha. We employ the perfect balance of diameter, length, fin width, fin depth, fin spacing, and grade of aluminum to cool your Yamaha as efficiently as possible. Two coolers can be used on the same machine. To install, drain coolant. Remove a section of your stock radiator hose. Replace it with the CFM-Hydrocooler. Tighten the stainless steel hose clamps, provided to you at no additional charge. Refill coolant. This engine cooler will reduce your coolant return temperature by an average of 8-12 degrees depending on engine modifications and riding conditions. Not only is this safer, but cooler engine operating temperature equals more horsepower.

(click image for larger photo) Yamaha Raptor 700 Grab Bar
Comes with flag and number plate mounting tabs. It is wider and much stronger than your stock grab bar. The number plate is sold seperately.

(click image for larger photo) Yamaha Raptor 700 High Flow Exhaust Tip
The most restrictive part of your stock exhaust system is the 3/4" diameter hole in the exhaust tip. With your stock tip, the exhaust is forced to make a 90 degree turn through the spark arrestor and another 90 degree turn to come out the tip. With the CFM Performance high flow exhaust tip there are no restrictive 90 degree turns. The exhaust comes straight through an opening that is 30% larger than stock, and straight through a stainless steel spark arrestor screen. It bolts on in a few minutes with no modifications to your stock silencer, and it sounds great with out being too loud. This high performace exhaust tip makes a big difference in throttle response and top end horsepower. No jetting change is required, your fuel injection system will automatically compensate for it.

(click image for larger photo) Yamaha Raptor 700 Intake
Made from 6061 aluminum for high strength, light weight, and incredible corrosion resistance. The CFM high flow intake uses a high volume, high velocity plenum to increase horsepower, and throttle response, as well as top speed. In our testing, the Raptor was 4mph faster in 0-250 ft runs after installing this intake. It was also faster by 3mph in top speed. To install, you will need to remove your stock air box and drill out the four rivets holding the stock flange in place. Our high performance flange will bolt to the stock air box through these four holes. Your small, restrictive stock air filter will no longer work. You will need to purchase a UNI filter part number NU-4102ST or K&N filter part number HA-4250, available from CFM Performance. These air filters have 50% more open area than any filter available for the stock flange.

(click image for larger photo) Yamaha Raptor 700 Tie Rods
Set of polished billet aluminum tie rods for a Yamaha Raptor or YFZ450. Made from billet aluminum for extremely high strength and light weight. Custom lengths available for customers with aftermarket a-arms. Available with or without wrench flats for no additional cost, to be specified by buyer at time of purchase.

(click image for larger photo) Yamaha Raptor 700 Front Lowering Kit
This kit will lower the front of your Yamaha by 3" and make it 1" wider. With this kit installed your center of gravity is much lower allowing you to corner faster. It is very durable. Perfect for flat track, TT, trail riding, or drag racing.

(click image for larger photo) Yamaha Raptor 700 Rear Lowering Kit
Lower center of gravity for faster cornering. Perfect for motocross, trail riding, flat track, tt, or drag racing. Will lower the rear of your Raptor about 4". Easy to install or remove. This kit replaces the stock strut that runs parallel to the swing arm. You will need to use the hardened steel bushings that are in your stock rear strut.

(click image for larger photo) Yamaha Raptor 700 Air Box
It is made from 5052 aluminum for high strength, light weight, and incredible corrosion resistance. The CFM high flow air box uses a high volume, high velocity plenum to increase horsepower, and throttle response, as well as top speed. The inside diameter of your stock filter is only 2 1/2". We go all the way up to a 4" inside diameter. In our testing, the Raptor was 4mph faster in 0-250 ft runs after installing this air box. It was also faster by 3mph in top speed. Your small, restrictive stock air filter will no longer work. You will need to purchase a UNI filter part number NU-4102ST or K&N filter part number HA-4250, available from CFM Performance.

(click image for larger photo) Yamaha Raptor 700 Coolant Bottle Guard
Made by CFM Performance from 5052 aluminum for high strength, light weight, and superior corrosion resistance. Protects your coolant bottle from being destroyed by debris. Features a slotted sight window that still allows you to keep an eye on coolant level.

(click image for larger photo) Yamaha Raptor 700 Scoop Kit
Made from 5052 series aluminum for high strength, light weight, and excellent corrosion resistance. This scoop kit bolts to the under side of your front fenders using the stock fender mounting bolts. It can be installed in less than three minutes. It will direct more air to your engine and exhaust header to help keep your Raptor running cooler.

(click image for larger photo) Yamaha Raptor 700 Oil Tank
The most efficient way to cool the oil in your Raptor is by increasing the oil capacity. This oil tank holds about an extra quart of oil. Made with precision machined fittings, and it is welded in a fixture for a perfect fit. Built with 5052 series aluminum for high strength and excellent corrosion resistance.